Blade Edge

Computer software | Video production | My life in general

Blade Edge games header

Flight Log – Quarry Disaster

November 1st, 2013 · No Comments · Gaming

So I wasn’t able to fly on Thursday, however since the flight I had planned would take place within a relatively small area I could use REX’s archive weather feature to load up weather for a given time of day and fly with that. So I found some decent yet not-perfect conditions late in the morning of 10/31 and loaded that into the sim. I had crafted the scenario beforehand with some default objects from FSX and the Acceleration add-on pack. I wanted to do another medevac airlift after the one I did in Niagara, and I originally planned to fly to Put-In-Bay airport out on Middle Bass Island since that had a helipad. The situation would be a critical patient that was driven from his home to the airport to be picked up by the chopper. But then I realized that was a pretty lame scenario and besides, I had just flown there before in the Staggerwing. So I looked around the Cleveland scenery area a bit more. I considered a shooting on the University campus that had photoreal texture coverage, but they have a university medical center and overall the distance was too short. I really wanted to head back out to the islands. Then I spotted this open mining pit on Kellys Island, which I learned was a limestone quarry. I don’t know if it’s still operational or not but frankly for this purpose I didn’t care as the entire situation is fictional to begin with. So I checked out various FSX objects and found one that produced explosions and fires – perfect! Then I just set about a few props, some actors – and I was ready to go.

There are two medical pads in the Cleveland scenery so I decided to depart from one and arrive at another. I chose to depart from the ground pad and arrive on the roof pad because that was more challenging. Plus the hospital with the roof pad was closer on the return trip. I used SkyVector to take a simple bearing from the helipad to the island, which I dialed into my HSI and simply followed that all the way out to the island. The Bell 222 has twin turbine engines, so if one flamed out on me I could continue with the other, no need to stick close to land like I had with the Staggerwing. The direct flight lasted about 20 minutes as I zoomed out near redline at 140kts. The 222 feels a lot more sensitive than the 206 but part of it is the VSI on the 222 is a lot bigger than the 206, so where the needle shows 500fpm climb on the 222 I would read more as a 1,000fpm climb in the 206. So it took me a while to adjust back to that.

I came up on the island without any trouble, the bearing worked perfectly. I circled in to land when all of the sudden I crashed in mid-air. I thought at first I had somehow overstressed the airframe since I was pushing redline the whole way there, but then I noticed the message from the sim stated I had collided with an object, not torn apart my chopper. That’s when I realized I had smacked into the bounding box defining the very large explosion area object I had set. God dammit. So after the situation reloaded and dumped me back at St. Vincent’s I went into my scenery editing tools and disabled crash detection for the explosion area object like I should have thought to do when I first built the damn thing. Then I had to fly out all over again, but this time at least I was able to approach and land without any trouble. Ok well, without crashing at least. I made a great initial approach but in attempting to spin about to present my loading side to the patient I almost lost it and had to just drop her down and then taxi around to face the right way.

Once I had the patient loaded it was back in the air and back near redline to race back to Cleveland so this guy could get proper treatment. However I realized after the flight that I had forgotten to go into the weight and fuel menu and change the passenger load after I had “picked up” my patient and a medical doctor that would treat and monitor him on the way to the hospital. I realize I also didn’t do this during my last medevac scenario. I did think about doing this beforehand this time, but just completely forgot during the actual event. Maybe next time.

I also forgot to make sure I knew where the blasted hospital was for my return trip. Luckily I knew generally where it was and spotted it on my first pass over the area. I belatedly called Lakefront ATIS to get wind direction, which I should have done much earlier, then circled around to approach the pad. Jesus crap it was tiny. I managed to make the approach clean and land without having to circle again, so I’ll say that my patient was at least alive when he left the helicopter and didn’t die while waiting for me to get the bird on the ground. I also didn’t jar him into a cardiac arrest as I landed at a gentle 1.4 ft/s. Honestly though in reality I never got to the offloading stage because I went to taxi forward a bit more to turn about and present my loading doors to the hospital roof door and started to fall through the helipad. So I said screw it and captured a shot of me on the pad from the instant replay.

Now, I plan to hop back over to the Cessna 337 down in the tropics but before that I have a shit ton of work to get done this month and I don’t know when that flight will happen. I will be uploading the airlift situation to AVSIM like I did with my last one. The link to download it is here.

Tags: ······